Quick Order   |  Gift & Wish Lists   |   Log In   

Aqua Lift Muffler C-30

Aqua Lift Muffler C-30

Part #: K1795

Please call for pricing & availability

This original equipment muffler is no longer available. See "May we also suggest:" below for the new design replacement muffler.

Original equipment, fiberglass Aqua Lift Muffler. We typically see this muffler configuration installed in the Catalina 30 with an M-25XP engine. There may be other models that use this configuration also.

Don't be tempted to replace your muffler with anything but the original design! Catalina's design is simple, but it is no accident. It has the right geometry and volume to minimize the possibility of water flowing back into the engine when the boat heels. A customer's report illustrates the point:

During a re-power by a very well respected yard, it was suggested the muffler be replaced with an "upgraded" production built muffler. After all of the money spent for the new engine, the customer felt it was a smart idea.

Motoring out the first day, the new engine performed beautifully. But after a fine sail, the engine refused to start. Back at the yard, water was discovered in the engine! After much time, confusion, work, and expense (for the yard), the engine was rebuilt and they were back sailing... with the same result!.

After two engine rebuilds, they finally realized the problem was with the muffler design. Water from the muffler was flowing into the engine through an open exhaust valve when the boat heeled under sail.

Two ways I have seen an old muffler fail are:
1) The seam at the bottom edge can fail. This can sometimes be repaired by removing the muffler. After a thorough cleaning, you may be able to saturate the failed joint with WEST epoxy, clamp and allow to cure.

CAUTION! The muffler must be pressure tested to 5 PSI while immersed in a water bath to check for leaks after any repair is attempted. Carbon monoxide is colorless, odorless, tasteless, AND DEADLY. If it leaks after your repair, YOU COULD KILL SOMEONE. We highly recommend the installation of a carbon monoxide detector.

2) The bond between the inlet tube and the box itself can fail. This typically occurs because the vibration of the engine is transmitted directly through a rigid hose to the stationary muffler. In this case, it is impossible to achieve a successful repair. Even with the installation of a new hump hose to help isolate the vibration (which we highly recommend), there will be much vibration transmitted to the fiberglass tube. To be strong enough, the repair would have to be made on the inside of the muffler where you have no access. In order to leave the enough fiberglass tube exposed for the hump hose, a repair from the outside would be too small to be secure enough given the serious safety concerns involved.

  • Base: 13-1/2" X 14-1/4"
  • Top: 11-1/2" X 12"
  • For additional dimensions, see the photo below under "More images"

    If you decide to replace your old muffler you will need to confirm the dimensions above and the dimensions on the photo below under "More images" match the muffler in your boat. We have no way to guarantee this is the muffler installed in your boat as Catalina didn't maintain records as to which muffler design was installed in each hull. If the dimensions match, it is the correct muffler. If the dimensions don't match, order our Aqua Lift Muffler, Custom part #Z2877 pictured below.

    This is an oversize item which does not conform to our standard shipping policies. Call 800/959-SAIL for a shipping estimate.

  • More Images: (click to enlarge)

    May we also suggest:
    No Image
    Exhaust Hump Hose 1-5/8"I.D X 6"

    No Image
    Exhaust Hump Hose 1-5/8"I.D. x 8"

    No Image
    Aqua Lift Muffler Drain Valve

    No Image
    Aqua Lift Muffler Drain Valve Tap

    No Image
    Aqua Lift Muffler C-30 New Design

    No Image
    Aqua Lift Muffler, Custom