Various articles covering frequently asked questions, informative bits of information, and even a spot of humor.
Our free tech support line is manned by a small team of sailors with decades of experience.
| 10210 Systems Parkway, Suite 390 Sacramento, CA 95827 |
|
| [email protected] | |
| 1-800-959-SAIL (7245) |
Since new rigging stretches, replacing only one of a pair of shrouds will make it difficult to keep your rig in tune.
You should “pre flight” and “post flight” your rig before and after every sail. Every time you sail in more wind than you have sailed in previously with your new rigging, it must be re-tuned.
Since rigging fails inside of the end fittings where they cannot be inspected, prudence dictates that standing rigging be replaced every seven years for boats sailed in salt water, every ten years for those sailed in fresh water.
No, you can choose one of our Trim-2-fit kits instead. There were many unrecorded changes in dimensions, turnbuckle length and hardware used by Catalina. Each of these changes can effect the length of your shroud or stay.
If you are sending old rigging to be duplicated, tune your rig, then mark your turnbuckles per our “Standing Rigging Instructions” found below under “Technical Support”.
It's difficult to tune your rig perfectly straight. That's OK. We fabricate your new rigging by averaging the length of each pair of shrouds.
Your new standing rigging will be fabricated to match the overall pin to pin dimension (+-1/4”) with the new turnbuckle adjusted approximately 1/3 of the way into it total available travel.
New rigging wire will stretch each time you sail in more wind. Having the turnbuckle 1/3 into its available travel provides more adjustment to accommodate that stretch.
Maybe. The swaged stud at the bottom of the forestay must pass through the furler. This is possible with most CDI Flexible Furlers, Hood and Schaefer furlers. Some Harken furlers and the Schaefer SnapFurl are too small for the swaged stud to pass through. If you can pull your old forestay out of the top of the furler without cutting the wire, you will likely be able to install a complete replacement forestay in its place.
Use our Trim-2-Fit forestay. Pass the unfinished end through the furler before using two wrenches to install the second end.
A thrust washer is required above the stud. If the foil accidentally drops onto the stud, the thrust washer will prevent the rotating foil from resting on the top of the stud and potentially causing the stud to rotate.
Call Technical Support with:
Catalina never installed Harken furlers and we can’t know what a previous owner might have installed. We can only help if you provide the above information.
Since new rigging stretches, replacing only one of a pair of shrouds will make it difficult to keep your rig in tune.
You should “pre flight” and “post flight” your rig before and after every sail. Every time you sail in more wind than you have sailed in previously with your new rigging, it must be re-tuned.
Since rigging fails inside of the end fittings where they cannot be inspected, prudence dictates that standing rigging be replaced every seven years for boats sailed in salt water, every ten years for those sailed in fresh water.
No, you can choose one of our Trim-2-fit kits instead. There were many unrecorded changes in dimensions, turnbuckle length and hardware used by Catalina. Each of these changes can effect the length of your shroud or stay.
If you are sending old rigging to be duplicated, tune your rig, then mark your turnbuckles per our “Standing Rigging Instructions” found below under “Technical Support”.
It's difficult to tune your rig perfectly straight. That's OK. We fabricate your new rigging by averaging the length of each pair of shrouds.
Your new standing rigging will be fabricated to match the overall pin to pin dimension (+-1/4”) with the new turnbuckle adjusted approximately 1/3 of the way into it total available travel.
New rigging wire will stretch each time you sail in more wind. Having the turnbuckle 1/3 into its available travel provides more adjustment to accommodate that stretch.
Maybe. The swaged stud at the bottom of the forestay must pass through the furler. This is possible with most CDI Flexible Furlers, Hood and Schaefer furlers. Some Harken furlers and the Schaefer SnapFurl are too small for the swaged stud to pass through. If you can pull your old forestay out of the top of the furler without cutting the wire, you will likely be able to install a complete replacement forestay in its place.
Use our Trim-2-Fit forestay. Pass the unfinished end through the furler before using two wrenches to install the second end.
A thrust washer is required above the stud. If the foil accidentally drops onto the stud, the thrust washer will prevent the rotating foil from resting on the top of the stud and potentially causing the stud to rotate.
Call Technical Support with:
Catalina never installed Harken furlers and we can’t know what a previous owner might have installed. We can only help if you provide the above information.
Catalina Direct is the largest supplier of Catalina Yacht parts in the country. We specialize in parts, custom up-grades, and accessories. Worldwide delivery available.
