Quick Order   |  Gift & Wish Lists   |   Log In   




  Pipe Sizes and Why They Are So Confusing

Pipe Sizes and Why They Are So Confusing

02/09/16

 

 

 

 

Every discussion about pipe and fitting sizes starts in a state of confusion. That is because, unless you are a plumber, it is natural to assume that the 1-1/2” elbow you have in your hand measures one and one-half inches… somewhere. In fact, only plumbers are taught that one’s logical assumption is not true.


Like dimensional lumber, where a 2 X 4 does not measure 2” by 4” there is no dimension on a piece of pipe or plumbing where the actual measurement matches the nominal size.


There are also many different thread designs depending upon their purpose, history, the area of the world they were first developed and the standards authority that establishes the standards. Here are just a few examples:

  • NPT:  National Pipe Thread Taper
  • NPTF: Dryseal American National Standard Taper Pipe Thread (ANSI B1.20.3)?NPT threads may be referred to as MPT ('Male Pipe Thread'), MNPT, or NPT(M) for male (external) threads
  • FPT ('Female Pipe Thread'), FNPT, or NPT(F) for female (internal) threads. Note that FPT and MPT are not authorized designations per the ANSI standard.
  • ISO: Thread pitch is usually measured in millimeters. Threads have 55° taper angle versus 60° for NPT. The NPT root and crest configurations are also different from ISO.

Most actual plumbing parts aboard (with the excepeion of through hull fittings) are NPT and look like this:

 

 

Characteristics of NPT (also known as ANSI/ASME B1.20.1 Pipe Threads, General Purpose):

  • Tapered thread 1° 72'
  • 60° thread angle
  • Pitch is measured in threads per inch
  • Truncation of roots and crests are flatImportant notes: 

Important tidbits:

  • For NPT threads a sealant compound or Teflon tape must be used for a leak-free seal. 
  • Each thread size has a defined number of threads per inch - TPI, or pitch. For example, both 1/2" and 3/4" NPT pipe has 14 threads per inch, therefore both the TPI and OD of the thread are required for positive identification of thread size.
  • NPT threads are not interchangeable with NPS - National Pipe Straight - threads.
  • NPT threads may look similar to ISO 7/1 threads. However, ISO and NPT threads should not be mixed. 

NPT - American Standard Pipe Thread Taper 

Nominal Pipe Size 

(inches)

Threads per Inch

TPI - pitch

Approximate Length of Thread (inches)

Approximate Number of Threads to be Cut

Approximate Total thread Makeup, Hand and Wrench (inches)

Nominal Outside Pipe Diameter

OD (inches)

Tap Drill

(inches)

1/16"

27

 

 

 

0.313

 

1/8"

27

3/8

10

1/4

0.405

R

1/4"

18

5/8

11

3/8

0.540

7/16

3/8"

18

5/8

11

3/8

0.675

37/64

1/2"

14

3/4

10

7/16

0.840

23/32

3/4"

14

3/4

10

1/2

1.050

59/64

1"

11-1/2

7/8

10

9/16

1.315

1-5/32

1-1/4"

11-1/2

1

11

9/16

1.660

1-1/2

1-1/2"

11-1/2

1

11

9/16

1.900

1-47/64

2"

11-1/2

1

11

5/8

2.375

2-7/32

2-1/2"

8

1 1/2

12

7/8

2.875

2-5/8

3"

8

1 1/2

12

1

3.500

3-1/4

 



Products
No Image
Elbow Fresh Water Quick Connect Male PEX

No Image
Aqua Lift Muffler Drain Valve

No Image
Engine Exhaust Flange Circular,
"B" Series Engine


No Image
Engine Exhaust Flange Female Circular,
"B" Series Engine


No Image
Engine Exhaust Flange Rectangular

No Image
Seacock, 3/4" FPT Marelon

No Image
Shower Valve Cockpit C-42 <-94 with Hose & Sprayer

No Image
Shower Head for Cockpit Shower 2005->

No Image
Galley Faucet

No Image
Galley Faucet, Pull Out

No Image
1/2" Ball Valve

No Image
1-1/2" Ball Valve

No Image
3/4" Ball Valve

No Image
Hose Barb 1/2" 90 Degree Elbow

No Image
Hose Barb 1/2" Straight

No Image
Hose Barb 1-1/2" 90 Degree Elbow

No Image
Hose Barb 3/4" 90 Degree Elbow

No Image
Hose Barb 3/4" Straight

No Image
Pure Water Starter Kit

No Image
Head Mixer Faucet, Hose & Shower Head C-350, C-387

No Image
Head Mixer Faucet C-42 Pullman

No Image
Shower Handle Only Head Mixer Faucet & Stand Alone Shower

No Image
Water Pump Replacement or Retrofit, 1/2" Oberdorfer

No Image
Water Pump Replacement or Retrofit, 3/8" Oberdorfer

No Image
Water Pump, 1/2" Oberdorfer, Repl for 1/2" Sherwood

No Image
Water Pump, Late Sherwood 1/2"

No Image
Water Pump Adapter Elbow, 5/8" x 1/2" NPT

No Image
Head Mixer Faucet with Shower on Hose

No Image
Elbow Fresh Water Quick Connect Female PEX

No Image
Plumbing Quick Connect Stem Adapter 15mm

No Image
Aqua Lift Muffler Drain Valve Tap

No Image
Galley Spray Head Replacement

No Image
Jabsco Macerator Pump

No Image
Sea Water Strainer

No Image
Temperature Sender Universal Diesel 1/8" NPT

No Image
Water Heater 11 Gal Galv Connections Front & Rear

No Image
Water Heater 6 Gal Galv
Connections Front & Rear


No Image
Hose for Pull-Out Galley or Head Faucet

No Image
Temperature Sender Universal Diesel 1/4" NPT

No Image
Shower Hose for Cockpit Shower 120" White PVC

No Image
Shower Valve for
Cockpit Shower 2005->


No Image
High Temp Alarm Retrofit
M-12, M2-12, M-30


No Image
High Temp Alarm Retrofit M-18, M-25, M-25XP, M-35

No Image
Hose Barb 1-1/2" Straight